PIC16F87T-I/ML【PDF 66/200 页】IC MCU FLASH 4KX14 EEPROM 28QFN

收藏本站

您好，
买卖IC网欢迎您。
请登录
免费注册

买卖IC网

Sheet目录3882

62页 63页 64页 65页 [66页]67页 68页 69页 70页

158

8008H–AVR–04/11

ATtiny48/88

Bit 5 – TWSTA: TWI START Condition Bit

The application writes the TWSTA bit to one when it desires to become a Master on the 2-wire

Serial Bus. The TWI hardware checks if the bus is available, and generates a START condition

on the bus if it is free. However, if the bus is not free, the TWI waits until a STOP condition is

detected, and then generates a new START condition to claim the bus Master status. TWSTA

must be cleared by software when the START condition has been transmitted.

Bit 4 – TWSTO: TWI STOP Condition Bit

Writing the TWSTO bit to one in Master mode will generate a STOP condition on the 2-wire

Serial Bus. When the STOP condition is executed on the bus, the TWSTO bit is cleared auto-

matically. In Slave mode, setting the TWSTO bit can be used to recover from an error condition.

This will not generate a STOP condition, but the TWI returns to a well-defined unaddressed

Slave mode and releases the SCL and SDA lines to a high impedance state.

Bit 3 – TWWC: TWI Write Collision Flag

The TWWC bit is set when attempting to write to the TWI Data Register – TWDR when TWINT is

low. This flag is cleared by writing the TWDR Register when TWINT is high.

Bit 2 – TWEN: TWI Enable Bit

The TWEN bit enables TWI operation and activates the TWI interface. When TWEN is written to

one, the TWI takes control over the I/O pins connected to the SCL and SDA pins, enabling the

slew-rate limiters and spike filters. If this bit is written to zero, the TWI is switched off and all TWI

transmissions are terminated, regardless of any ongoing operation.

Bit 1 – Res: Reserved Bit

This bit is reserved and will always read as zero.

Bit 0 – TWIE: TWI Interrupt Enable

When this bit is written to one, and the I-bit in SREG is set, the TWI interrupt request will be acti-

vated for as long as the TWINT Flag is high.

15.11.3

TWSR – TWI Status Register

Bits 7:3 – TWS: TWI Status

These 5 bits reflect the status of the TWI logic and the 2-wire Serial Bus. The different status

codes are described later in this section. Note that the value read from TWSR contains both the

5-bit status value and the 2-bit prescaler value. The application designer should mask the pres-

caler bits to zero when checking the Status bits. This makes status checking independent of

prescaler setting. This approach is used in this datasheet, unless otherwise noted.

Bit 2 – Res: Reserved Bit

This bit is reserved and will always read as zero.

Bit

(0xB9)

TWS7

TWS6

TWS5

TWS4

TWS3

–

TWPS1

TWPS0

TWSR

Read/Write

R/W

Initial Value

发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

*型号	*数量	厂商	批号	封装

添加更多采购

采购需求

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

我的联系方式